Cisco UCME / UC500 (AKA Call Manager Express)

These instructions should assist in configuring your Cisco UCME / UC500 to work with TIM Plus. If you are not familiar with PBX configuration, please contact your system maintainer.

There are two ways to connect to the Cisco UCME / UC500: RADIUS (RADIUS events are recommended by Cisco) SysLog (Requires SysLog server, not all CDR data received from router)

These instructions should assist in configuring your Cisco UCME / UC500 to work with TIM Plus. If you are not familiar with PBX configuration, please contact your system maintainer.

There are two ways to connect to the Cisco UCME / UC500: RADIUS (RADIUS events are recommended by Cisco) SysLog (Requires SysLog server, not all CDR data received from router)

RADIUS configuration for Cisco UCME / UC500

The tasks required to be done are as follows. They are all analysed in details further down this page.

1. Download TIM Plus and complete setup wizard
2. Configure TIM Plus to receive data from UCME / UC500
3. Configure Cisco AXL Sync
4. Set up RADIUS to send call events to TIM Plus

1.  Downloading TIM Plus and completing the setup wizard

1. Visit Tri-Line's Portal and download the TIM Plus installation package, as shown below:

2. Run the installation package and on Stage 5 complete the following details:

• Site name: Enter a description for the site
• PBX model: Select Cisco UCME - RADIUS
• Method: Select RADIUS Connection
• Client IP: Enter the IP Address of the Cisco UCME / UC500
• Secret: Enter a RADIUS authentication secret to allow TIM Plus and UCME / UC500 to communicate e.g. C1sco. Please note that this will need to be added to your UCME / UC500 configuration later on.

2.  Configuring TIM Plus to receive data from UCME / UC500

Below you will find steps on how to configure your TIM Plus to receive data from UCME / UC500:

1. Browse to TIM Plus as normal and login with your credentials.
2. Click on the Directory tab.
3. Click on the site configured during the setup wizard and click Properties or create a new site and click Properties.

4. Within the Site Properties window, select Cisco UCME - RADIUS from the PBX model drop-down list.
5. In the Connection method field select RADIUS connection from the drop-down list.
6. In the Client IP field enter in the IP Address of the Cisco UCME / UC500.
7. In the Secret field enter in the password you set during phase 1.  Downloading TIM Plus and completing the setup wizard e.g. C1sco.
8. To enable data backup, click on the Options tab.

9. Click on the Save a backup of any data received from this PBX tick box.
10. Finally, click on the Save button.

3.  Configuring Cisco AXL sync

Below you will find steps on how to configure the Directory Sync from Cisco UCM:

1. Browse to TIM Plus as normal and login with your credentials.
2. Click on the Directory tab.
3. Click on the site configured during the setup wizard and click Properties or create a new site and click Properties.
4. Within the Site Properties window, select the Sync tab.
5. Click on the Synchronise with the following device tick box.

6. In the Host field enter in the IP Address of your UCME / UC500.
7. In the Username field enter in the username to login to your UCME / UC500.
8. Click on the Set button and enter the password used to login to the UCME / UC500, followed by clicking OK.
9. Finally, click on the Save button.

TIM Plus will now connect to the PBX and sync the directory objects.

4.  Setting up RADIUS to send call events to TIM Plus

Login to your Cisco UCME / UC500 via telnet, as shown below:

Now just enter the following RADIUS commands:

SysLog configuration for Cisco UCME / UC500

The tasks required to be done are as follows. They are all analysed in details further down this page.

1. Download TIM Plus and complete setup wizard
2. Configure TIM Plus to receive data from UCME / UC500
3. Configure Cisco AXL Sync
4. Set up SysLog to send call events to TIM Plus

1.  Downloading TIM Plus and completing the setup wizard

1. Visit Tri-Line's Portal and download the TIM Plus installation package, as shown below:

2. Run the installation package and on Stage 5 complete the following details:

• Site name: Enter a description for the site
• PBX model: Select Cisco UCME - SysLog
• Method: Select SysLog Connection
• Client IP: Enter the IP Address of the Cisco UCME / UC500

2.  Configuring TIM Plus to receive data from UCME / UC500

Below you will find steps on how to configure your TIM Plus to receive data from UCME / UC500:

1. Browse to TIM Plus as normal and login with your credentials.
2. Click on the Directory tab.
3. Click on the site configured during the setup wizard and click Properties or create a new site and click Properties.

4. Within the Site Properties window, select Cisco UCME - SysLog from the PBX model drop-down list.
5. In the Connection method field select SysLog connection from the drop-down list.
6. In the Client IP field enter in the IP Address of the Cisco UCME / UC500.
7. To enable data backup, click on the Options tab.

8. Click on the Save a backup of any data received from this PBX tick box.
9. Finally, click on the Save button.

3.  Configuring Cisco AXL sync

Below you will find steps on how to configure the Directory Sync from Cisco UCM:

1. Browse to TIM Plus as normal and login with your credentials.
2. Click on the Directory tab.
3. Click on the site configured during the setup wizard and click Properties or create a new site and click Properties.
4. Within the Site Properties window, select the Sync tab.
5. Click on the Synchronise with the following device tick box.

6. In the Host field enter in the IP Address of your UCME / UC500.
7. In the Username field enter in the username to login to your UCME / UC500.
8. Click on the Set button and enter the password used to login to the UCME / UC500, followed by clicking OK.
9. Finally, click on the Save button.

TIM Plus will now connect to the PBX and sync the directory objects.

4.  Setting up SysLog to send call events to TIM Plus

Login to your Cisco UCME / UC500 via telnet, as shown below:

Now just enter the following SysLog commands: